what is Powder Coating MSDS
![powder coating msds](https://www.chinapowdercoatpowder.com/wp-content/uploads/2013/12/powder-coating-msds-300x295.png)
Powder Coating MSDS
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: Powder Coating
MANUFACTURE/DISTRIBUTOR: Jinhu Color Powder Coating Co., Ltd
Address: Dailou Industrial Zone,Jinhu County,Huai’an,China
Emergency Response Call:
2. COMPOSITION/INFORMATION ON INGREDIENTS
HAZARDOUS INGREDIENTS : CAS No. WEIGHT (%)
Polyester resin : 25135-73-3 60
Epoxy resin : 25085-99-8 20
Barium sulfate: 7727-43-7 10
Pigments: N/A 10
3. HAZARDS IDENTIFICATION
Primary Routes of Exposure : Skin Contact,Eye Contact .
Inhalation :Inhalation of dust or mist caused during heating and processing can cause irritation of nose, throat and lungs,headache,nausea
Eye Contact :Material can cause irritation
Skin Contact : Prolonged or repeated skin contact can cause irritation
Ingestion :Material is possibly harmful if swallowed.
4. FIRST AID MEASURES
Inhalation :If exposed to toxic fumes from heating or combustion, move subject to fresh air.
Eye Contact:Flush eyes with a large amount of water for at least 15 minutes. Consult a physician if irritation persists.
Skin Contact:Wash affected skin areas thoroughly with soap and water. Consult a
physician if irritation persists. Wash contaminated clothing thoroughly before reuse. Do not take clothing home to be laundered.
Ingestion: If swallowed, give 2 glasses of water to drink. Consult a physician. Never
give anything by mouth to an unconscious person.
5. FIRE FIGHTING MEASURES – POWDER COATING MSDS
Flash Point:Not Applicable
Auto-ignition Temperature:No Data
Lower Explosive Limit:Not Applicable
Upper Explosive Limit:Not Applicable
Unusual Hazards:Combustion generates Smoke, soot, and toxic/irritating fumes (i.e., carbon dioxide, carbon monoxide, etc.).
Extinguishing Agents:carbon dioxide,dry chemical,foam,water spray
Personal Protective Equipment:Wear self-contained breathing apparatus (pressure-demand NIOSH approved or equivalent) and full protective gear.
Special Procedures:Remain upwind. Avoid breathing smoke. Use water spray to cool containers exposed to fire.
6. ACCIDENTAL RELEASE MEASURES
Personal Protection: Appropriate protective equipment must be worn when handling a spill of this material. See SECTION 8, Exposure Controls/Personal Protection, for recommendations. If exposed to material during clean-up operations, see SECTION 4, First Aid Measures, for actions to follow.
Procedures: Floor may be slippery; use care to avoid falling. Transfer spilled material to suitable containers for recovery or disposal. Keep dust to a minimum.
CAUTION: Keep spills and cleaning runoff out of municipal sewers and open bodies of water.
7. HANDLING AND STORAGE
Handling Procedures: Do not handle material near food, feed or drinking water.
Storage Conditions: Avoid temperature extremes during storage; ambient temperature preferred. Material can burn; limit indoor storage to approved areas equipped with automatic sprinklers. Do not store this material near food, feed or drinking water. Keep container tightly closed when not in use.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Exposure Limit Information
ACGIH – TLV
Titanium Dioxide 10 mg/M3
Barium sulfate(dust) 10 mg/M3 Total
Polyester resin. . . . . . . . . None
Epoxy resin. . . . . . . . . . . None
OSHA – PEL
Titanium Dioxide 10 mg/M3
Barium sulfate(dust) 10 mg/M3 Total
Polyester resin. . . . . . . . . None
Epoxy resin. . . . . . . . . . . None
Engineering Controls (Ventilation): Use adequate ventilation or local exhaust.
Respiratory Protection: None required under normal operating conditions. When dusty conditions are encountered, wear a approved half-mask, air-purifying respirator.
Eye Protection: Use safety glasses.
Hand Protection: Cotton or canvas gloves.
Other Protective Equipment: Facilities storing or utilizing this material should be equipped with an eyewash facility.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: powder Solid
Explosion limits: Not available.
Specific gravity (water=1): Not Applicable
pH: Not available.
Viscosity: Not Applicable
10. STABILITY AND REACTIVITY
Instability: This material is considered stable.
Incompatibility: There are no known materials which are incompatible with this product.
Hazardous Decomposition Products: Combustion generates Smoke, soot, and toxic/irritating fumes (i.e., carbon dioxide, carbon monoxide, etc.).
Hazardous Polymerization: Product will not undergo polymerization.
11. TOXICOLOGICAL INFORMATION
Acute Data
No toxicity data are available for this material.
12. ECOLOGICAL INFORMATION
No Applicable Data
13. DISPOSAL CONSIDERATIONS
Procedure
For disposal, incinerate or landfill at a permitted facility in accordance with local, state, and federal regulations .
The above recommendation covers disposal of material as supplied.
14. TRANSPORT INFORMATION
We hereby confirm above goods belongs to common chemical product which
is not in the list of <>
15. REGULATORY INFORMATION
Inventory of exiting chemical substance (SEPA): The hazardous components in this product are all listed.
List of dangerous Chemicals (SAWS et al,2002 ed): Product – none.
Identification of major hazard installations (GB18218-2000): Product- none.
List of high toxic substance (2003): none.
The National Catalogue of Hazardous Wastes (SEPA, 10998): Waste dyes and paints (HW12).
16.OTHER INFORMATION
This manual is based on data provided by all of our knowledge, information and existing publications.
Data Audit Unit: Shanghai Center of Toxic Chemicals Information & Consultation
2012-08-17
Powder Coating MSDS